Refer to the exhibit.
What does the command channel-group 1 mode desirable do？ （）
A.enables LACP unconditionally
B.enables PAgP only if a PAgP device is detected
C.enables PAgP unconditionally
D.enables Etherchannel only
E.enables LACP only if a LACP device is detected
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA.
Which two statements are true about the possible result of attaching the second link？（）
A.The switch port attached to LinkB will not transistion to up.
B.One of the two switch ports attached to the hub will go into blocking mode when a BPDU is received.
C.Both switch ports attached to the hub will transition to the blocking state.
D.A heavy traffic load could cause BPDU transmissions to be blocked and leave a switching loop.
E.The switch port attached to LinkA will immediately transition to the blocking state.
A.All ports will temporarily transition to the learning state for a period equal to the max age timer plus the forward delay interval.
B.All ports will transition temporarily to the learning state for a period equal to the forward delay interval.
C.The default aging time for MAC address entries will be reduced for a period of the max age timer plus the forward delay interval.
D.The default hello time for configuration BDPUs will be reduced for the period of the max age timer.
A.The port immediately transitions to the Forwarding state.
B.The switch generates a Topology Change Notification （TCN） BPDU.
C.The port immediately transitions to the err-disable state.
D.The port becomes a normal STP switch port.
A.RSTP information is automatically aged out.
B.The port sends a TCN to the root bridge.
C.The port moves to listening state.
D.The port becomes a normal spanning tree port.
A.CEF， distributed CEF （dCEF）， fast switching， process switching
B.distributed CEF （dCEF）， CEF， fast switching， process switching
C.fast switching， process switching， distributed CEF （dCEF）， CEF
D.process switching， fast switching， distributed CEF （dCEF）， CEF
E.process switching， distributed CEF （dCEF）， CEF， fast switching
F.process switching， CEF， distributed CEF （dCEF）， fast switching
A.LACP is used to connect to non-Cisco devices.
B.LACP packets are sent with the command channel-group 1 mode desirable.
C.LACP packets are sent with the command channel-group 1 mode active.
D.Standby interfaces should be configured with a higher priority.
E.Standby interfaces should be configured with a lower priority.
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit，
which two statements are true？（）
A.Changing the bridge priority of S1 to 4096 would improve network performance.
B.Changing the bridge priority of S1 to 36864 would improve network performance.
C.Changing the bridge priority of S2 to 36864 would improve network performance.
D.Changing the bridge priority of S3 to 4096 would improve network performance.
E.Disabling the Spanning Tree Protocol would improve network performance.
F.Upgrading the link between S2 and S3 to Gigabit Ethernet would improve performance.
A.The BID is made up of the bridge priority value（two bytes） and bridge MAC address （six bytes）.
B.The BID is made up of the bridge priority （four bits）， the system ID （12 bits）， and a bridge MAC address （48 bits）.
C.The BID is made up of the system ID （six bytes） and bridge priority value （two bytes）.
D.The system ID value is the VLAN ID （VID）.
E.The system ID value is a unique MAC address allocated from a pool of MAC addresses assigned to the switch or module.
F.The system ID value is a hex number used to measure the preference of a bridge in the spanning-tree algorithm.
Based on the show spanning-tree vlan 200 output shown in the exhibit，
which two statements about the STP process for VLAN 200 are true？ （）
A.BPDUs will be sent out every two seconds.
B.The time spent in the listening state will be 30 seconds.
C.The time spent in the learning state will be 15 seconds.
D.The maximum length of time that the BPDU information will be saved is 30 seconds.
E.This switch is the root bridge for VLAN 200.
F.BPDUs will be sent out every 10 seconds.
A.HSRP
B.GLBP
C.VRRP
D.SLB
E.RPR
F.RPR+
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. Which statement is true about the output？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Which two statements are true when the extended system ID feature is enabled？ （）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
What two things will occur when an edge port receives a BPDU？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）