A.VLAN instance mapping and revision number
B.VLAN instance mapping and member list
C.VLAN instance mapping, revision number, and member list
D.VLAN instance mapping, revision number, member list, and timers
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct,
what will be true about Switch 15?()
A.All ports will be in forwarding mode.
B.All ports in VLAN 10 will be in forwarding mode.
C.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in blocking mode.
D.All ports in VLAN 10 will be in forwarding mode and all ports in VLAN 20 will be in standby mode.
A.BPDU port-guard can be enabled globally, whereas BPDU filtering must be enabled on a per-interface basis.
B.When globally enabled, BPDU port-guard and BPDU filtering apply only to PortFast enabled ports.
C.When globally enabled, BPDU port-guard and BPDU filtering apply only to trunking-enabled ports.
D.When a BPDU is received on a BPDU port-guard enabled port, the interface goes into the err-disabled state.
E.When a BPDU is received on a BPDU filtering enabled port, the interface goes into the err-disabled state.
F.When a BPDU is received on a BPDU filtering enabled port, the interface goes into the STP blocking state.
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:
00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex).
What would be the possible outcome of the problem?()
A.The root port on switch SW_A will automatically transition to full-duplex mode.
B.The root port on switch SW_B will fallback to full-duplex mode.
C.The interfaces between switches SW_A and SW_B will transition to a blocking state.
D.Interface Fa 0/6 on switch SW_B will transition to a forwarding state and create a bridging loop.
A.mon Spanning Tree maintains a separate spanning-tree instance for each VLAN configured in the network.
B.The Spanning Tree Protocol (STP) is an evolution of the IEEE 802.1w standard.
C.Per-VLAN Spanning Tree (PVST) supports 802.1Q trunking.
D.Per-VLAN Spanning Tree Plus(PVST+) is an enhancement to 802.1Q specification and is supported only on Cisco devices.
E.Rapid Spanning Tree Protocol (RSTP) includes features equivalent to Cisco PortFast, UplinkFast, and BackboneFast for faster network reconvergence.
F.Multiple Spanning Tree (MST) assumes one spanning-tree instance for the entire Layer 2 network, regardless of the multiple number of VLANs
Refer to the exhibit. For what purpose is the command show ip cef used?()
A.to display rewritten IP unicast packets
B.to display ARP resolution packets
C.to display ARP throttling
D.to display TCAM matches
E.to display CEF-based MLS lookups
F.to display entries in the Forwarding Information Base (FIB)
Refer to the exhibit. Which statement is true about the output?()
A.The port on switch CAT1 is forwarding and sending BPDUs correctly.
B.The port on switch CAT1 is blocking and sending BPDUs correctly.
C.The port on switch CAT2 is forwarding and receiving BPDUs correctly.
D.The port on switch CAT2 is blocking and sending BPDUs correctly.
E.The port on switch CAT3 is forwarding and receiving BPDUs correctly.
F.The port on switch CAT3 is forwarding, sending, and receiving BPDUs correctly.
Refer to the exhibit.
What does the command channel-group 1 mode desirable do? ()
A.enables LACP unconditionally
B.enables PAgP only if a PAgP device is detected
C.enables PAgP unconditionally
D.enables Etherchannel only
E.enables LACP only if a LACP device is detected
Refer to the exhibit. Initially, LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA.
Which two statements are true about the possible result of attaching the second link?()
A.The switch port attached to LinkB will not transistion to up.
B.One of the two switch ports attached to the hub will go into blocking mode when a BPDU is received.
C.Both switch ports attached to the hub will transition to the blocking state.
D.A heavy traffic load could cause BPDU transmissions to be blocked and leave a switching loop.
E.The switch port attached to LinkA will immediately transition to the blocking state.
A.All ports will temporarily transition to the learning state for a period equal to the max age timer plus the forward delay interval.
B.All ports will transition temporarily to the learning state for a period equal to the forward delay interval.
C.The default aging time for MAC address entries will be reduced for a period of the max age timer plus the forward delay interval.
D.The default hello time for configuration BDPUs will be reduced for the period of the max age timer.
A.The port immediately transitions to the Forwarding state.
B.The switch generates a Topology Change Notification (TCN) BPDU.
C.The port immediately transitions to the err-disable state.
D.The port becomes a normal STP switch port.
最新試題
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result?()
Refer to the exhibit. Which Virtual Router Redundancy Protocol (VRRP) statement is true about the roles of the master virtual router and the backup virtual router?()
Which three statements about STP timers are true?()
During routine maintenance, it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time, DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ? ()
If G1/0/1 on DS1 is shutdown, what will be the current priority value of the Vlan105’s group on DS1 ?()
Refer to the exhibit. Initially, LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link?()
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()
Which statement is correct about the use of the virtual interface on a WLC ?()
Refer to the exhibit. What does the command channel-group 1 mode desirable do? ()
Which two statements about the various implementations of STP are true?()